How To Use And Maintain Oscillating Knife CNC Cutter?
Here are some steps about how to use and maintain an oscillating knife CNC cutter:
Using the Oscillating Knife CNC Cutter
-
Initial Setup: Ensure the machine is placed on a flat surface and all hardware components are securely attached according to the manufacturer's instructions. Connect the machine to a power source and turn it on, checking for any error messages during the boot-up process.
-
Calibration: Before starting any cutting job, calibrate the machine to ensure accurate operation. Align the tool head to be perfectly vertical and use the calibration tool provided by the manufacturer to properly align the blade. Update the software and enter the correct parameters such as material type, thickness, and cutting speed.
-
Test Cut: Run test cuts on scrap materials to verify the accuracy of the settings. Make necessary adjustments until the desired results are achieved.
Oscillating Knife CNC Cutter Maintenance
To make our oscillating knife CNC cutter can use longer life, super durable. In addition to the normal use method, regular maintenance and maintenance are also essential. So how to maintain, small compiled some, for your reference.
1. the requirements for environment when using vibration knife should be placed in places where the sun light cannot be exposed or the surface of the shade can avoid the rupture caused by direct sunlight on the table. The cutting machine shall be placed in a dry place, and the cutting place shall not be equipped with inflammable, explosive or combustible materials.
2. when working with the vibration cutter, please operate it in the way of video and observe the warning on the equipment in accordance with the warning words.
3. pay attention to the safety of power consumption, and configure the power box in advance according to the factory requirements to ensure that the power supply can meet the stability of the equipment in use.
4. before starting cutting, the insulation of power cord and cutting cable shall be carefully checked.
5. before starting work, the cutting parameters shall be adjusted, and the parameters shall be adjusted according to the actual materials to be cut. It is not allowed to adjust too much at a time, which is prone to the phenomenon of knife breaking and cutting off conveyor belt, etc. which may damage the damaged equipment.
6. cut off all input power supply of cutter after cutting, and clean the work and cutting machine table.
7. if the cutter fails, it can be used only after the fault is eliminated due to the timely shutdown and inspection. If you are in trouble with the problem, please consult with the after-sales personnel of eppon in time.
8. the vibration knife shall be maintained regularly. Click to see how to maintain the vibration cutter.
9. clean and clean the dust regularly and wipe the table surface. It is best to use alcohol to directly disinfect. Keep the machine and guide rails clean.
10. add oil to the spindle bearing of the vibration knife regularly to ensure it can work normally.
11. regularly check the belt and grinding wheel of vibration cutter for cracks. If any cracks are found, the professional maintenance personnel shall be informed to handle them immediately.
12. it is also a crucial link to check the computer system of vibration cutter regularly. The computer system is directly related to whether the vibration cutter can work normally, so the computer system should be maintained, poisoned and optimized regularly.
13. abnormal noise occurs during the use of vibration cutter. It is necessary to turn off the power immediately and find out the reasons. It is necessary to inform the maintenance personnel of the equipment to carry out professional maintenance and test.
14. as long as it is machine and equipment, it is dangerous. It should be used strictly according to the normal operation process. If you are in use, you have to leave in the middle of the way. It is necessary to turn off the power supply to avoid the use of other personnel violating the regulations, and cause dangerous injury to the safety of the machine and personal.
15. regularly check the rotating part of the blade head of the vibration knife, monitor the vulnerable parts at any time, and maintain the record best. If the parts need to be replaced at the expiration, prepare for replacement in advance.
16. the machine is important, and the technical level of the operator is also very important. The operators should be trained regularly to improve their operation level. The quality of work will be improved. Operators must be trained to work on duty. Without the consent of technical personnel, they cannot operate without permission. To avoid incurable damage to yourself and the machine.
17. Regular Cleaning: Clean the machine thoroughly every week, focusing on the horizontal and vertical guide rails, transmission gears, and racks. Use a clean, dry cloth to wipe down the surfaces and remove any dust or debris.
18. Lubrication: Apply lubricant to the moving parts of the machine, such as the guide rails and bearings, to reduce friction and wear. Follow the manufacturer's recommendations for the type and frequency of lubrication.
19. Inspect and Replace Worn Parts: Regularly check for wear and tear on components like belts, bearings, and cutting tools. Replace any worn parts promptly to prevent machine malfunctions.
20. Blade Inspection: Check the cutting blades for dullness or damage and replace them as needed to maintain cutting accuracy.
21. Software Updates: Keep the machine's software up to date with the latest versions to benefit from new features, bug fixes, and performance enhancements.
22. Calibration Checks: Periodically recalibrate the machine to ensure consistency between programmed cuts and actual results. This involves checking the alignment of the tool head and the calibration of the blade.
By following these steps, you can ensure that your oscillating knife CNC cutter operates efficiently and lasts longer, providing consistent high-quality cuts.